DOCUMENT #2071

JUMPER SETTINGS AND PORTS OK TEST
FACT:  WHEN YOU INSTALL A NEW DATA CHIP ALWAYS MAKE SURE THE JUMPERS
       ARE JUMPED PROPERLY OR IT WILL GIVE YOU PROBLEMS.

   NORMAL JUMPER SETTINGS                                       PORTS OK TEST
      JMP 4,7,8,10                                               JMP 4,7,8,9 
          ÚÄÄÄ¿                                                     ÚÄÄÄ¿      
          ³ * ³                                                     ³ * ³      
    JMP 2 >   <                                               JMP 2 >   <      
          ³ * ³                                                     ³ * ³      
    JMP 3 >   <                                               JMP 3 >   <      
          ³  ³                                                     ³  ³      
    JMP 4 > ± <                                               JMP 4 > ± <      
          ³  ³                                                     ³  ³      
    JMP 5 >   <                                               JMP 5 >   <      
          ³ * ³           THIS                                      ³ * ³      
    JMP 6 >   <                                               JMP 6 >   <      
          ³  ³               IS                                    ³  ³      
    JMP 7 > ± <                                               JMP 7 > ± <      
          ³  ³                 FOR                                 ³  ³      
          >   <                                                     >   <      
          ³  ³                    OLD                              ³  ³      
    JMP 8 > ± <                                               JMP 8 > ± <      
          ³  ³                       SYSTEM                        ³  ³      
          >   <                                                     >   <      
          ³ * ³                             SETTINGS                ³  ³      
    JMP 9 >   <                                               JMP 9 > ± <      
          ³ * ³                                                     ³  ³      
          >   <                                                     >   <      
          ³  ³                                                     ³ * ³      
    JMP10 > ± <                                               JMP10 >   <      
          ³  ³                                                     ³ * ³      
          ÀÄÄÄÙ                                                     ÀÄÄÄÙ      
PORTS OK TEST SETTINGS:                                      
                                                                               
Setup the jumpers as shown.  Disconnect the serial port and remote port cables. 
Run program 88 and watch the screen.  It should say "PORTS OK".  PORTS OK means
that the SERIAL PRINTER and the SMDR port are functioning property.
                                                                               
   NORMAL JUMPER SETTINGS                                       PORTS OK TEST
       JMP 3,6,8,9                                              JMP 3,6,8,10    
          ÚÄÄÄÄ¿                                                    ÚÄÄÄÄ¿
    JMP 2 ³  ³                                              JMP 2 ³  ³
    JMP 3 ³Íͳ          THIS                                JMP 3 ³Íͳ
    JMP 4 ³  ³              IS                              JMP 4 ³  ³
    JMP 5 ³  ³                FOR                           JMP 5 ³  ³
    JMP 6 ³Íͳ                   NEW                        JMP 6 ³Íͳ
    JMP 7 ³  ³                      SYSTEM                  JMP 7 ³  ³
    JMP 8 ³Íͳ                            SETTINGS          JMP 8 ³Íͳ
    JMP 9 ³Íͳ                                              JMP 9 ³  ³
    JMP 10³  ³                                              JMP 10³Íͳ
          ÀÄÄÄÄÙ                                                    ÀÄÄÄÄÙ